Tuesday, January 11, 2011

Ground School Class 3

Altimeter Gauge
Altimeter
Attached to the static air port, a sealed bladder inside the altimeter gauge inflates and deflates with changes in air pressure. The changes in size are transfered via a series of gears and levers to drive the gauge needle. A small dial and window allows for the setting of the current barometric pressure so the instrument reads the correct distance to the ground.

There are several types of altitude:

Indicated - altitude above sea level.
Pressure - 29.92 inches of mercury is the standard datum.
Density - pressure corrected for non-standard temp.
True (MSL) - Above Mean Sea Level.
Absolute (AGL) - Above Ground Level.

The allowable altimeter error for ILR flight is 75ft. Any greater error and the aircraft is no longer legal to fly.

The altimeter needs adjustment every so often (every 100 miles or so) to account for the changes in atmospheric pressure. This is especially important when traversing from high pressure to low pressure or from high to low temperature. As the pressure or temp drops the un-adjusted altimeter starts to show an increase in altitude, causing a correction that is descending rather than maintaining level flight.

There are a few ways to make the altimeter adjustments. The radio is the most common - as you pass near different airports, you can listen in to their ASOS or other automated weather broadcasts that will state the current barometric readings for the area.

Vertical Speed Indicator
Vertical Speed Indicator
Also connected to the static port, the VSI indicates the aircrafts rate of climb or descent in feet per minute. The trend is always accurate; if the needle shows accent, you're climbing, if ti shows descent, you're descending. However the rate indicated has some lag and takes a few seconds to settle down and provide and accurate reading.

Gyroscopic Instruments
These instruments use gyroscopes and the principle of rigidity in space, as the aircraft essentially rotates around the instruments. Gyros are either electric or vacuum powered.

Attitude Indicator
Attitude Indicator
The attitude indicator is also known as the eight ball. It show the pitch and roll of the aircraft in a single reading. The attitude indicator uses a vacuum powered gyroscope.

Directional Gyroscope
Directional Gyro
The directional gyro is just a stabilized compass. It needs to be adjusted via the magnetic compass every 15 minutes in order to remain accurate.

Turn Coordinator
Turn Coordinator
The turn coordinator uses the combination of an electric gyroscope and gravity to help the pilot make good coordinated turns using just the right amount of rudder.

"Whiskey Compass"
Magnetic Instruments
This means the regular compass or "whiskey" compass. It's just a ball floating in liquid, so the compass is hard to read in flight due to it's bouncing around all the time. The instrument has mass and is affected by acceleration, deceleration when traveling east or west and leads or lags turns when traveling north or south. The compass reads magnetic north and all navigation charts are based on true north. Our sectional charts provide the information to calculate a heading correction. An isogonic line follows the curve of the earths magnetic field. The difference between the isogonic line reading and true north is used to correct your navigation heading.

Forces of Flight
There are four forces of flight:

  1. Lift
  2. Thrust
  3. Weight (Gravity)
  4. Drag
When in level, non-accelerated flight, all four forces are in equilibrium.

Lift & Wings
Lift is generated by the wings. The wing elements are the leading edge, trailing edge, camber and the chord-line. The chord-line is an imaginary line drawn straight between the center of the leading edge and the center of the trailing edge. The angle of incidence is the angle that the wings are attached to the fuselage. The angle of attack is the angle between the chord-line and the relative wind. The wing will always stall at the same angle of attack, regardless of air speed.


Saturday, January 8, 2011

A flying goal update...

On May 24th of this year, I have the opportunity to give a 30 minute presentation about the organization that I work for. Unfortunately, it's all the way out in the city of Pasco, WA. a 281 mile drive from Vancouver or a 4.5 hours drive each way. Can you see where this is going?

I talked to my instructor and inquired if it was feasible for me to perform a solo cross-country flight to the Tri-Cities Regional Airport within that time frame. Turns out that the school has an approved list of destinations for cross-country excursions and Pasco is not on that list. There is some difficult terrain between Vancouver and Pasco and it is complicated by being, well...complicated. There are eight runways in a cross configuration and a passenger terminal.

However, Theresa did think it would be a great idea for a dual-received cross-country flight. The flight time is around 2 hours each way. This ought to be pretty cool. Fly in, tell my professional peers how awesome Empower Up is, buy my instructor lunch and then fly on home in time for dinner.

Thursday, January 6, 2011

Ground School Class 2

Fuel Systems
Fuel Systems
There are two types of fuel systems: gravity fed and pressurized. Gravity fed systems are utilized in high wing aircraft (like the C-150) and are just like they sound, gravity allows fuel to flow from the wing tanks down to the engine. In low wing aircraft, the engine is higher than the wings and a pressurized system that utilizes an engine driven pump pushes fuel up from the wing tanks. Pressurized systems also have electric fuel pumps so that fuel can be pumped with out the engine turning and can serve as booster pumps.

The fuel tanks are (usually) located in the wings. Fuel tanks are either a bladder inside the wing or what is called a wet wing, where the tank is an integral part of the wing itself. All planes must have at least one fuel quantity gauge. However, they are notoriously inaccurate and flight plans are based on fuel consumption rates which will be covered later on. A fuel selector valve allows the pilot to switch between tanks and keep the weight of fuel in the wings balanced while in flight. Each wing tank has a fuel strainer on the bottom that allows fuel to be drawn out and be inspected for water contamination. There is now only one grade of av-gas (100LL) that is tinted blue so you can distinguish it from jet fuel.

Oil System
Oil does four things in the engine. Provides lubrication and cooling as well as carries particulates away and removes them via the oil filter and finally provides a seal in the cylinder. Aircraft are required to have two gauges: oil temp and oil pressure.

Cooling System
Aircraft engines are air cooled. The cowling is designed to maximize the air flow over the cylinders. Some aircraft are equipped with cowl flaps, that are pilot controlled and can increase cooling during climbs, but can be closed to reduce drag during cruise speeds.

Props
There are two types of props - fixed and constant speed. A fixed prop is a single blade that comes in two types of configurations: climb and cruise. Climb props are efficient climbers, but not good for cruising. Cruise prop is just the opposite. Prop is chosen based on the most common use of the particular aircraft. A constant speed prop is also referred to as a variable pitch prop, as is pilot adjustable in flight. Fixed prop engines speeds are monitored via an tachometer. Constant speed prop engine speeds are regulated using a combination of a tachometer, a manifold pressure gauge and the chosen prop pitch.

Electrical System Diagram
Electrical System
Aircraft systems use either a generator (in older planes) or an alternator. An alternator system creates an A/C that is then converted to D/C to power the avionics and other systems. Aircraft use either 14V or 28V systems and are monitored via a load meter or an ammeter. The electrical system is controlled by a master switch that is a two part rocker switch, with one side for the battery and one side for the alternator. The system is protected by either fuses or circuit breakers. All the electrical components are usually tied together via two bus bars, a primary bus and an avionics bus.

Flight Instruments
The discussion on flight instruments starts with a primer on atmospheric pressure. A standard day refers to sea level elevation and 15 C (59 F) which is 29.92 inches of barometric pressure. There is a loss of 1 inch of pressure for every 1,000 ft change in elevation. Atmospheric pressure is measured via two instrument ports: the pitot tube and the static port. The pitot tube is just what is sounds like , a small tube that points forward and the amount of air pressure that passes thru the tube changes with the speed of the aircraft. The static port is a small port that is located perpendicular to the forward direction and and measures the static atmospheric pressure. The airspeed indicator (ASI) measures the difference between the pitot tube pressure and the static port pressure. Two other gauges are attached to the static port: the altimeter and the vertical speed indicator. The airspeed indicator has gauge markings for several V speeds.

ASI
Vs = stall speed indicated by the bottom of the green arc.
Vso = stall speed in the landing configuration (flaps extended and gear down) indicated by the bottom of the white arc.
Vfe = flap extension speed, or the maximum speed that you safely extend flaps
Vno = normal operating range indicated by the top of the green arc.
Vne = never to exceed speed indicated by the red line.

The difference between the Vno and the Vne is the caution range indicated by the yellow arc.

There are several other V speeds that are not indicated on the ASI because they vary with the weight of the aircraft or other parameters that are listed in the POH.

Va = maneuvering airspeed.
Vx = best climb angle
Vy = best rate of climb
Vglide = best glide speed
Vlo = landing gear operating speed
Vle = landing gear extended speed

There are four different types of airspeed:

IAS = indicated airspeed
CAS = calibrated airspeed
TAS = true airspeed
GS = ground speed.

We'll be covering this more when we get to flight planning.

Monday, January 3, 2011

Ground School Class 1

The class is pretty small with only 4 students, so we should be able to get into topics in some detail. Topics included an overview of pilot training, pilot certification, medical certificates, aircraft certification and the various additional training and endorsements needed to fly different types aircraft such as multi-engine, high performance, complex and sea planes. We also did a brief overview of human factors (causes of human error) and physiology.

The Major Components
Then we jumped into the topic of aircraft components - with a brief overview of fuselage, monocoque and semi-monocoque construction, wings, control surfaces, landing gear, brakes and the power plant. Wrapping up this section was a discussion of the required paperwork that all planes need to have in them at all times.

Due to our small class size, we got thru that section pretty quickly and jumped ahead to the next section that got into more detail regarding the power plant. Basics of reciprocating engines, carburetors (and the dreaded carburetor ice). We very briefly discussed super chargers and turbo chargers and we started to cover the ignition system.

Magneto System
Ignition System
The ignition system in small aircraft doesn't require an electrical system. The system is driven by two separate magnetos that each power one of two sets of spark plugs. This provides a critical redundancy that will allow the engine to get operating even when one magneto fails. Pretty handy, huh? This also means that you want to make sure both magnetos are off if you're moving the propeller. It can suddenly fire the engine and...well you get the idea. The system is controlled by an ignition switch that can be switched from left, right and both magnetos. This allows the pilot to isolate each side of the system and is done so during the start-up procedure.

Next class we'll continue power plant systems and flight instruments.

Flight Five - Slow Flight Maneuvers

The drag curve.
Todays lesson dealt with slow flight and landing patterns. Theresa and I did a quick pre-flight briefing to discuss how this would proceed in flight; discussing the concepts of parasitic and induced drag and how this relates to best glide speed.

This morning was quite cold (temp. was 33 degrees at the time of start-up) and so we spent some amount of time brushing ice off the wings and removing any moisture from inside the cockpit windscreen to prevent frosting as we climbed to colder altitudes.

Start-up was a bit more complicated, more fuel priming, and three attempts to get the cold engine fired up and running smooth. I performed the walk around by myself this time and it's becoming more and more familiar each time. After the start-up check list, we listened to the Pearson Field automated weather (135.12) and then Theresa had me talk to Pearson Control (123.00) and the tower at PDX (119.00) for the first time. i.e: "Portland tower this is four x-ray alpha, on the ramp at Pearson, taxiing to runway 08 for a departure to the north." Now it feels like I'm a pilot. My taxiing is still improving and I'm starting to feel pretty comfortable getting the plane to go right where I want it to.

After yet another unassisted take-off, we headed north over Vancouver lake and then climbed to 2,500 ft. to start the slow flight maneuvers. We started out at 100 kts and made a few rudder assisted turns to get the feel for the plane at cruising speed. We then dropped speed to 80 and tried a few more turns...and I could really feel the difference. The ailerons lose effectiveness and the rudder becomes more effective. We dropped to 60 kts, each speed drop making turns just a bit more difficult. Next we flew at 40 kts which is less than best glide speed and so the plane needs to be pitched up at a pretty steep angle to maintain level flight, kind of a weird sensation. After a few more turn series, we headed back to Pearson to practice landing pattern approaches.

Approaching at 1,000 ft we reduce power by turning on the carb. heat and decreasing the throttle. Then we add 10 degrees of flaps and pitch down gently, decending towards the runway. We keep adding flaps, 20 degrees, then 40 degrees. Allowing us to lose altitude while maintaining airspeed. As we approached the  runway, I could see we were in the glide path (red lights over white lights), dropped the throttle to idle and and made my final adjustments, then it was full throttle, raising the flaps in increments until we climbed out and turned into the downwind approach to try it again. The second approach, I came in a bit high, but not too high. Once more around, and this time we were going to land. Theresa let me (sort of) land again and we were done for this flight.

In our debriefing, we discussed where the lessons would go from here. Next is more slow flight, this time with fake landings in the air as practice for real landings. In theory, I could do a real landing the next time out. A solo flight maybe possible in just a few more flights after that...oh shit!

Hours of flight logged this lesson: 1.2 Dual Received (DR)
Cost of this lesson: $165.81

Baby, it's cold outside!

Morning frost on X-ray Alpha
I have a flight lesson scheduled for 10am this morning, and it is currently 30 degrees outside. Doc and I walked down by the airfield this morning around 8am, just after the sun was coming up to scope out how frosty the planes are. They're pretty frosty. I dropped into the pilots lounge and chatted with the operations manager about my flight this morning, and he suggested we go out and turn the plane I reserved so in was pointing into the rising sun. There are no clouds this morning, so hopefully a little solar radiation will defrost the plane in time. My instructor has a flexible schedule today and we will push back the lesson time if need be.

Sunday, January 2, 2011

Flight Simulator Upgrade

C152 Cockpit (simulator)
I just installed a Cessna 152 into my flight sim software (FSX) and I got my USB rudder pedal controller to work properly (finally!). Now I can practice with a plane that is almost exactly like the C-150's I've been flying for realz. The pedals controller has differential brakes, so taxiing is much more realistic. The 152's cockpit layout is just like the 150's, so my check list practice is also much better (no more fudging around the minor differences). I just wrapped up a brief sim. flight and it works great!

Next lesson is scheduled for 10:00am tomorrow morning (the time may be pushed back if it's too cold). The first class of ground school is later the same evening.

Thursday, December 30, 2010

Ground School

Private Pilot Training Kit
Ground school starts on Monday. I dropped by the flight center to pick up my class materials and pay off the balance for the class. The school credited me for the log book that I purchased earlier, but otherwise shown to the right is everything in the kit I received:
  • Private Pilot Manual
  • Private Pilot Maneuvers Manual
  • Private Pilot FAA Practical Test Guide
  • Private Pilot Airmen Knowledge Guide
  • Pre-Solo Written Exam
  • Student Slide-Graphic Computer (E6B)
  • PN-1 Navigation Plotter
  • Pilot Logbook (credited for one I purchased for my first flight).
  • 2011 FAR/AIM Manual
  • Map Holder
  • Flight Bag
School consists of 16, two and a half hour classes held Monday and Wednesday nights for the next 8 weeks. Total cost for classes and materials $538.49 (includes $50 deposit and $13.49 for Log Book purchased earlier). Now I just need to read the first two chapters of the Pilot Manual before Monday's class.


Monday, December 6, 2010

Flight Four - Ground Reference Maneuvers (cont.)

The weather decided to cooperate and more flight training was possible this morning. Our cloud ceiling today was over 4,000 ft. (my instructor won't let us go up if the ceiling is under 1,500 ft.) and the winds were not too bad (4-7 knots, gusts up to 12 kts). We spent a bit more time on the weather during pre-flight and used the animated radar maps to make sure there weren't any columns of bad weather moving in that could affect visibility when we approached to land later this morning.

Duct tape? Really?
Pre-flight walk around is going much faster. The left wing tip light housing apparently hit something...the maintenance crew duct taped it...cool. I'm flying a plane that is actually held together with tape...why this amuses me more than it disturbs me? No idea.

My taxiing is also improving. I'm still not comfortable with talking to ATC at PDX, so I still let Theresa handle all the radio calls. She is drilling me on it every call though. "Location and action". Where am I? What to I want to do? Apparently there is a section during ground school that will help me feel more comfortable with getting the format right.

Take-off was from runway 08, with enough wind to make it much more interesting than the first few flights. The aircraft really bounced around...really felt like flying now! Headed north to the fair grounds and started with todays lesson - more ground reference maneuvers, this time flying a 1/2 mile radius circle around a fixed point at 1,000 ft. AGL. Theresa was really pleased we had some wind for these maneuvers. Flying a level circle in the wind is kinda hard. The wind is pushing you places you don't want to go and it's varying constantly as the bearing to the wind changes.

Theresa demonstrated this once and then I was in control and did real well as the turns were counter clockwise - or rather on the pilots side of the plane. Not easy, but manageable. Then we started the circle in the other direction and it was much more difficult. On my first attempt I lost sight of my ground reference point before I started my first turn. It got better, but was really challenging.

Over Ridgefield, WA
On the way back to Pearson, Theresa showed me how to perform 180 s-turns over I-5. I finally had more than a brief few seconds of non-busy time and actually took another picture (the camera in my phone sucks). By this time we were getting close to our time limit, so I took the controls and headed us southwest towards Vancouver Lake and started descending for our approach. Theresa let me land this time (sort-of, she really has a her hands and feet on the controls and corrects any lame flying I attempt in the process).

After we landed, Theresa asked me if I was really as calm as I seemed during the flight. I am. This feels so natural to me. Anyways, she's so pleased with my progress/demeanor that we're going to get into more complex maneuvers involving more radical power changes next time...as a prep to really landing by myself.

It was good to get back in the air again after missing out last month. Maybe Santa will pay for a another lesson before the year is out.

Hours of flight logged this lesson: 1.0 Dual Received (DR)
Cost of this lesson and down payment for class: $202.41

Saturday, December 4, 2010

Monday! Monday! Monday!*

* blaring out of loud speaker system like a TV ad for a monster truck show.

The weather report for Monday is looking good enough to fly. Cloudy, high of 46 degrees...the afternoons the past few days have been pretty nice over the Vancouver/Metro area. Hopefully an early afternoon flight will be possible. Last Monday afternoon there was some beautiful weather prompting my instructor to e-mail me: "wanna fly?" but alas, Monday was the day BEFORE payday...so no flying.

With the overnight lows still in the mid-30's, morning flights will be difficult to schedule this time of year, due to the flying schools practice of not using the C-150's if they're covered with frost. An unfortunate engine design allows for significant ice buildup in the carburetor. The cure for which is to redirect some engine exhaust to melt the ice. Great cure, but it robs the C-150 of some horsepower, and the availability of full power at take-off is crucial to have for students like myself (you know...noobs).

While I'm on the subject of icing, the carburetor icing problem with the C-150 occurs in flight too. As you descend, there is a tendency for ice to build up in the carburetor throat. However, descending long enough for that to occur is usually at the same time your making an approach to an airfield. This makes a small loss of power irrelevant because you'll be decreasing the throttle anyway. Just one of the many little things you need to keep track of and remember while flying. There is no warning devise or alarm that sounds...if ice is allowed to build up too much...the engine dies, and it cannot usually be restarted in flight, because you need exhaust heat from a running engine to unfreeze things. So maybe not so little...upside: apparently the C-150 glides real good.

I think I'll go and reserve myself a plane right now.